iabdalkader
23d9898065
Update WINC1500 to Rev-B
2016-04-16 02:40:18 +02:00
iabdalkader
6ee32b89e2
Update Eagle files.
...
* Rename VIN to VCC on backside silkscreen
2016-03-11 02:29:14 +02:00
iabdalkader
a7874b8651
Update shields silk-screen.
2016-02-11 02:37:31 +02:00
iabdalkader
584e1ca58a
Update silkscreen
2016-02-10 01:25:01 +02:00
iabdalkader
07669d9258
Update Eagle files.
...
* Add OpenMV2-R5
2016-01-28 15:36:44 +02:00
iabdalkader
ab3b36c504
Add WiFi and BLE Shields.
2015-10-12 13:37:50 +02:00
iabdalkader
a6ff8e506f
Add OMV2 BOM
2015-09-10 02:25:05 +02:00
iabdalkader
3c55cefeb3
Rename Eagle files
2015-08-07 17:46:25 +02:00
iabdalkader
51b6b55c4f
Update silk screen
2015-08-07 17:35:08 +02:00
iabdalkader
ccc3375c91
Update design files
...
* Replace 1A TI regulator with BD 500mA.
* Replace ORing diodes with one dual common cathode.
2015-05-15 21:22:07 +03:00
iabdalkader
91087eae41
Update design files
2015-05-06 14:47:51 +03:00
iabdalkader
9ddaca0731
Add SWD
2015-03-02 00:01:53 +02:00
iabdalkader
56ee02e137
Add lbr dir
2015-03-02 00:00:22 +02:00
iabdalkader
0beb4d192a
Update openmv.lbr
2015-03-02 00:00:01 +02:00
iabdalkader
f2c438a4c3
Reorganize /eagle
2015-03-01 23:58:46 +02:00
iabdalkader
8e68ff3b27
Add Proto Shield
2015-02-27 05:04:54 +02:00
iabdalkader
40332bf13b
Add shields and update OMV3
2015-02-27 04:28:49 +02:00
iabdalkader
add9571548
Update HW
...
* Connect STROBE, FREX and EXPST_B
* Remove shield.
* Add pull-down to IR MOSFET
2015-02-23 01:17:55 +02:00
iabdalkader
466a54a752
Add new HW
2015-01-26 20:15:24 +02:00
iabdalkader
33d354339e
Move images to imgs dir, update README
2014-10-31 21:16:26 +02:00
iabdalkader
0aaa51bc26
Fix SDRAM part-no
...
* Issue #29
2014-10-31 19:21:41 +02:00
iabdalkader
b644a6cd83
Add OmniVision Eagle Library
2014-10-16 15:53:23 +02:00
iabdalkader
4dc27bbd7f
Add OpenMV Eagle Library
...
* Issue #21
2014-10-13 02:54:51 +02:00
iabdalkader
1b731a2aff
Add WiFi and BLE Shields
2014-10-07 05:09:54 +02:00
iabdalkader
0508c3ac54
Update board image
2014-10-05 03:16:09 +02:00
iabdalkader
e1e9b40cdc
Add board image
2014-10-05 03:15:02 +02:00
iabdalkader
2e40c29da1
Add OMV2 Eagle files
2014-09-28 14:22:12 +02:00
iabdalkader
5cdbec2a41
Remove old revisions
2014-09-28 14:18:32 +02:00
iabdalkader
6f7de049b1
Fix components values
2014-08-10 14:40:18 +02:00
iabdalkader
45c4b7f512
Add REV5.1
2014-07-15 08:53:59 +02:00
iabdalkader
6daea3bede
Add REV5
2014-06-14 18:39:49 +02:00
shimniok@gmail.com
821155bf1a
Readying for production run, fixed OSHPark DRC errors
2014-05-19 08:32:54 -06:00
iabdalkader
beb380a160
Add rev4-a
2014-05-07 01:41:35 +02:00
iabdalkader
35c817f040
Update REV4
...
* Replace regulator with ADP121xx
* Use the new crystal
* Fix USB connector
2014-04-18 01:13:29 +02:00
iabdalkader
c8e539a184
Update REV4
...
* Make more room for mounting holes, and dbg header
2014-04-13 20:35:17 +02:00
iabdalkader
c1588d7175
Update HW REV4
...
* Use dual LDO
* Add I2C EEPROM
* Update RESET switch
* Add bulk cap to STM VCC
* Add diode on debug VCC
* Add bead for sensor filter
* Use separate USART
2014-03-13 20:22:35 +02:00
iabdalkader
893921390a
Add debugger adaptor
...
* Add 2mm to 2.54mm debugger adaptor
2014-02-09 18:02:52 +02:00
iabdalkader
d4c7fed1d9
Update REV4
...
* Use a different I2C multiplexed with USART
2014-02-09 18:00:05 +02:00
iabdalkader
0339e80c96
Update REV4
...
* Add regulator test points
* Remove 10mil via
2014-01-29 21:22:14 +02:00
iabdalkader
48826fb1f6
Add new HW revision
...
* Remove power switch and its decoupling cap
* Resize the mounting holes to 2mm
* Connect the switch to NRST instead of BOOT0
* Change RGB LED footprint to PLCC-6
* Change switch footprint
* Add extra pads to usb connector
* Remove crystal and load caps, use ceramic resonator
2014-01-26 13:41:36 +02:00
iabdalkader
d45395eb38
Add 3rd hardware revision
...
* Replace single resistors with resistor networks.
* Add pull-ups to the uSD SPI signals and unused pins.
* Add a 2mm pitch debugging header.
* Breakout I2C3, SPI3 and USART3 using the main header.
* Fix silk screen component names.
* Connect the sensor's PWDWN and RESET to GPIO.
* Add a MOSFET load switch to enable/disable power to the uSD.
* Add a bulk cap to STM micro.
* Add a switch to enter the DFU mode.
2014-01-02 11:17:01 +02:00
iabdalkader
9ef9899041
Add test points to breakout SPI3
2013-12-13 02:56:42 +02:00
iabdalkader
0d8c75e0b4
Added the new hardware revision
...
Added missing DSP library
Fixed SysTick timer IRQ priority
userspace fixes
2013-12-06 03:40:57 +02:00
iabdalkader
b439bdae91
Initial commit
2013-11-13 12:24:56 +02:00