<b>Small Outline Transistor</b> >NAME >VALUE >NAME >VALUE >VALUE >NAME >VALUE <b>SUPPLY SYMBOL</b> <b>Voltage Regulator LDO</b> Standard 150mA LDO voltage regulator in SOT-23 layout. Micrel part MIC5205. BP (by-pass) pin is used to lower output noise with 470pF cap. >NAME >VALUE >Name >Value >Name >Value >Name >Value >NAME >VALUE <b>CAPACITOR</b><p> chip >NAME >VALUE >Name >Value >Name >Value >NAME >VALUE CTZ3 Series land pattern for variable capacitor - CTZ3E-50C-W1-PF >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE 2mm SMD side-entry connector. tDocu layer indicates the actual physical plastic housing. +/- indicate SparkFun standard batteries and wiring. >Name >Value + - >Name >Value >NAME >VALUE >NAME >VALUE This footprint was designed to help hold the alignment of a through-hole component (i.e. 6-pin header) while soldering it into place. You may notice that each hole has been shifted either up or down by 0.005 of an inch from it's more standard position (which is a perfectly straight line). This slight alteration caused the pins (the squares in the middle) to touch the edges of the holes. Because they are alternating, it causes a "brace" to hold the component in place. 0.005 has proven to be the perfect amount of "off-center" position when using our standard breakaway headers. Although looks a little odd when you look at the bare footprint, once you have a header in there, the alteration is very hard to notice. Also, if you push a header all the way into place, it is covered up entirely on the bottom side. This idea of altering the position of holes to aid alignment will be further integrated into the Sparkfun Library for other footprints. It can help hold any component with 3 or more connection pins. >NAME >VALUE >NAME >VALUE >NAME >VALUE >Name >Value + - >NAME >VALUE >Name >Value + - >Name >Value <b>RESISTOR</b><p> chip >NAME >VALUE <b>CAPACITOR</b><p> chip >NAME >VALUE 1/6W Thru-hole Resistor - *UNPROVEN* >NAME >VALUE >NAME >VALUE 1/4W Resistor, 0.4" wide<p> Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 1/2W Resistor, 0.5" wide<p> Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 1W Resistor, 0.6" wide<p> Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value 2W Resistor, 0.8" wide<p> Yageo CFR series <a href="http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf">http://www.yageo.com/pdf/yageo/Leaded-R_CFR_2008.pdf</a> >Name >Value >NAME >VALUE >NAME >VALUE >VALUE >NAME >VALUE >VALUE >NAME >VALUE >NAME >VALUE <b>SUPPLY SYMBOL</b> <b>Capacitor</b> Standard 0603 ceramic capacitor, and 0.1" leaded capacitor. <b>Header 2</b> Standard 2-pin 0.1" header. Use with straight break away headers (SKU : PRT-00116), right angle break away headers (PRT-00553), swiss pins (PRT-00743), machine pins (PRT-00117), and female headers (PRT-00115). Molex polarized connector foot print use with SKU : PRT-08233 with associated crimp pins and housings. <b>SUPPLY SYMBOL</b> <b>Resistor</b> Basic schematic elements and footprints for 0603, 1206, and PTH resistors. >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE 1 2 <b>Crystals</b> Various standard crystals. Proven footprints. Spark Fun Electronics SKU : COM-00534 >NAME >NAME OSHW >VALUE >VALUE >NAME <b>SUPPLY SYMBOL</b> <b>Frames for Sheet and Layout</b> Date: >LAST_DATE_TIME Sheet: >SHEET REV: TITLE: Document Number: >DRAWING_NAME <b>FRAME</b><p> DIN A3, landscape with extra doc field >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE Power Supply Modules Copyright (c) 2013 Ibrahim Abd Elkader <i.abdalkader@gmail.com> This work is licensed under the Creative Commons Attribution-ShareAlike 3.0 License. To view a copy of this license, visit http://creativecommons.org/licenses/by-sa/3.0/ 2 CC3000