>VALUE >VALUE <b>SUPPLY SYMBOL</b> <b>SUPPLY SYMBOL</b> >NAME >VALUE >Name >Value >Name >Value >Name >Value >NAME >VALUE >NAME >VALUE <b>CAPACITOR</b><p> chip >NAME >VALUE >Name >Value >Name >Value >NAME >VALUE CTZ3 Series land pattern for variable capacitor - CTZ3E-50C-W1-PF >NAME >VALUE >NAME >VALUE >NAME >VALUE >NAME >VALUE 2mm SMD side-entry connector. tDocu layer indicates the actual physical plastic housing. +/- indicate SparkFun standard batteries and wiring. >Name >Value + - >Name >Value >NAME >VALUE >NAME >VALUE This footprint was designed to help hold the alignment of a through-hole component (i.e. 6-pin header) while soldering it into place. You may notice that each hole has been shifted either up or down by 0.005 of an inch from it's more standard position (which is a perfectly straight line). This slight alteration caused the pins (the squares in the middle) to touch the edges of the holes. Because they are alternating, it causes a "brace" to hold the component in place. 0.005 has proven to be the perfect amount of "off-center" position when using our standard breakaway headers. Although looks a little odd when you look at the bare footprint, once you have a header in there, the alteration is very hard to notice. Also, if you push a header all the way into place, it is covered up entirely on the bottom side. This idea of altering the position of holes to aid alignment will be further integrated into the Sparkfun Library for other footprints. It can help hold any component with 3 or more connection pins. >NAME >VALUE >NAME >VALUE >NAME >VALUE >Name >Value + - >NAME >VALUE >Name >Value + - Small solder jumper with big paste layer so it will short during reflow. >NAME >VALUE Solder jumper, small, shorted with trace. No paste layer. Trace is cuttable. >NAME >VALUE >NAME >VALUE Small solder jumper with no paste layer so it will open after reflow. >NAME >VALUE >NAME >VALUE >NAME >VALUE >Value >Name >Name >Value >Name >Value <b>Panasonic Aluminium Electrolytic Capacitor VS-Serie Package G</b> >NAME >VALUE <b>Panasonic Aluminium Electrolytic Capacitor VS-Serie Package E</b> >NAME >VALUE <b>Panasonic Aluminium Electrolytic Capacitor VS-Serie Package E</b> >NAME >VALUE >NAME >VALUE >NAME >VALUE >Value >Name >Value >Name >NAME >VALUE >NAME >VALUE >VALUE >NAME >VALUE >VALUE >NAME >NAME >NAME >VALUE <b>SUPPLY SYMBOL</b> <b>Capacitor</b> Standard 0603 ceramic capacitor, and 0.1" leaded capacitor. <b>Header 2</b> Standard 2-pin 0.1" header. Use with straight break away headers (SKU : PRT-00116), right angle break away headers (PRT-00553), swiss pins (PRT-00743), machine pins (PRT-00117), and female headers (PRT-00115). Molex polarized connector foot print use with SKU : PRT-08233 with associated crimp pins and housings. <b>Solder Jumper</b> Standard SMD solder jumper. Used to automate production. Two varients : Normally Open and Normally Closed are the same, but have different paste layers. NC will have a large amount of paste and should jumper during reflow. <b>Capacitor Polarized</b> These are standard SMD and PTH capacitors. Normally 10uF, 47uF, and 100uF in electrolytic and tantalum varieties. Always verify the external diameter of the through hole cap, it varies with capacity, voltage, and manufacturer. The EIA devices should be standard. <b>Small Outline IC</b> >NAME >VALUE >VALUE TPS768 <b>SUPPLY SYMBOL</b> >Name >Value >NAME >VALUE >Name >Value >Name >Value <b>CAPACITOR</b><p> chip >NAME >VALUE >NAME >VALUE 1007 (2518 metric) package >NAME >VALUE >Name >Value >NAME >VALUE >NAME >VALUE 1.3x1.3mm 1.7mm between. Fits Sumida CDRH2D09, CDRH2D18 inductor >NAME >VALUE <b>CAPACITOR</b><p> chip >NAME >VALUE OSHW >NAME >VALUE >VALUE <b>Inductors</b> Basic Inductor/Choke - 0603 and 1206. Footprints are not proven and vary greatly between part numbers. <b>SUPPLY SYMBOL</b> <b>Frames for Sheet and Layout</b> Date: >LAST_DATE_TIME Sheet: >SHEET REV: TITLE: Document Number: >DRAWING_NAME <b>FRAME</b><p> DIN A3, landscape with extra doc field >NAME >VALUE >NAME >VALUE TI SimpleLink CC3000 Module - WiFi 802.11b/g Network Processor <b>Supply Symbols</b><p> GND, VCC, 0V, +5V, -5V, etc.<p> Please keep in mind, that these devices are necessary for the automatic wiring of the supply signals.<p> The pin name defined in the symbol is identical to the net which is to be wired automatically.<p> In this library the device names are the same as the pin names of the symbols, therefore the correct signal names appear next to the supply symbols in the schematic.<p> <author>Created by librarian@cadsoft.de</author> >VALUE <b>SUPPLY SYMBOL</b> >NAME >VALUE >NAME >VALUE Power Supply Modules Copyright (c) 2013 Ibrahim Abd Elkader <i.abdalkader@gmail.com> This work is licensed under the Creative Commons Attribution-ShareAlike 3.0 License. To view a copy of this license, visit http://creativecommons.org/licenses/by-sa/3.0/ 2 CC3000